Elesa+Ganter GN 5435 stainless steel star knob
Stainless steel AISI 316 L (A4)
- Matt (Ra < 0.8 µm) MT
- Polished (Ra < 0.8 µm) PL
Sealing ring: hydrogenated acrylonitrile butadiene rubber (H-NBR), blue
temperature resistant -25 °C to +150 °C
Hardness 85±5 Shore A
FDA compliant
Information
GN 5435 star knobs are intended for use in hygiene areas. The sealed mounting surface
enables mounting without dead spaces; the High quality finish and the large corner radius prevent adherence of dirt and faciliate cleaning
Elesa+Ganter GN 5445 stainless steel Three lobe knob
Stainless steel AISI 316 L (A4)
- Matt (Ra < 0.8 µm) MT
- Polished (Ra < 0.8 µm) PL
Sealing ring: hydrogenated acrylonitrile butadiene rubber (H-NBR), blue
temperature resistant -25 °C to +150 °C
Hardness 85±5 Shore A
FDA compliant
Information
GN 5445 Three lobe knob are intended for use in hygiene areas. The sealed mounting surface
enables mounting without dead spaces; the High quality finish and the large corner radius prevent adherence of dirt and faciliate cleaning
Elesa+Ganter VB.239 Three-arm knob
Material: High-strength, reinforced phenolic based (PF) Duroplast. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, glossy finish.
Standard execution:
Black-oxide steel hub with uncovered front end and pre-drilled blind hole. See table for maximum permissible boring diameters d' and d".
Elesa+Ganter VB.639 Three-arm knob
Material: Glass-fibre reinforced polyamide based technopolymer (PA) with the exception of VB.639/130 which is in glass-fibre reinforced polypropylene based (PP) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, matte finish.
Assembly
- Execution A: black-oxide steel boss, plain blind hole.
- Execution B: brass boss, tapped blind hole.
Elesa+Ganter VB.639 FP Three-arm knob
Material: Glass-fibre reinforced polyamide based technopolymer (PA) with the exception of VB.639/130 which is in glass-fibre reinforced polypropylene based (PP) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, matte finish.
Assembly: Brass boss, tapped through hole.
Elesa+Ganter VB.639 p Three-arm knob
Material: Glass-fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, matte finish.
Assembly: Zinc-plated steel threaded stud, chamfered flat end according to UNI 947 : ISO 4753 (see Technical Data ).
Elesa-Ganter three-arm knob VB.639-SST with stainless steel boss.
Material: Glass-fibre reinforced polyamide based technopolymer (PA) with the exception of VB.639/130 which is in glass-fibre reinforced polypropylene based (PP) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, matte finish.
Assembly: AISI 303 stainless steel boss, tapped blind hole.
Elesa+Ganter VCT. Lobe knobs with coloured centre cap
Material: High-resilience polypropylene based (PP) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, matte finish.
Coloured centre cap (only for VCT.32-40-50-63-74-95)
Technopolymer, matte finish.
To order, add the index of the colour (C9, ..., C6) to the code and the description.
On request and for sufficient quantities, it can be supplied in other colours or with customised graphic symbols, marks or writings.
Standard executions
- VCT-A: black-oxide steel boss, plain blind hole.
- VCT-B: brass boss, threaded blind hole (VCT.25 - 95) or threaded pass-through hole (VCT.32 - 40 - 50 - 63 - 74).
Colour codes centre caps:
C9 = Black RAL9005
C2 = Orange RAL2004
C3 = Grey RAL7035
C4 = Yellow RAL1021
C5 = Blue RAL5024
C6 = Red RAL3000
Elesa+Ganter VCT.p Lobe knob with coloured centre cap
Material: High-resilience polypropylene based (PP) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, matte finish.
Coloured centre cap (only for VCT.32-40-50-63-74-95)
To order, add the index of the colour (C9, ..., C6) to the code and the description.
On request and for sufficient quantities, it can be supplied in other colours or with customised graphic symbols, marks or writings.
Standard execution: Zinc-plated steel threaded stud, chamfered flat end according to UNI 947 : ISO 4753 (see Technical Data).
Colour codes centre caps:
C9 = Black RAL9005
C2 = Orange RAL2004
C3 = Grey RAL7035
C4 = Yellow RAL1021
C5 = Blue RAL5024
C6 = Red RAL3000
Elesa+Ganter CS.VCT Caps for Lobe knob
Colours:
Black RAL9005
Light blue RAL5024
Blue RAL5019
Grey RAL7035
Yellow RAL1021
Orange RAL2004
Red RAL3000
Elesa+Ganter VCT. FP Lobe knob
Material: High resilience polypropylene based (PP) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, matte finish.
Standard execution: Brass boss, threaded through hole.
Elesa+Ganter VCT.AE-V0 Lobe knob
Material: Glass-fibre reinforced polyamide based (PA) technopolymer certified self-extinguishing UL-94 V0. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, matte finish.
Assembly: Brass boss with tapped blind hole (VCT.25) or through hole (VCT. from 32 to 50).
Centre cap: Glass-fibre reinforced technopolymer certified self-extinguishing UL-94 V0, black colour, matte finish, supplied assembled.
Elesa+Ganter VCT.p SOFT Lobe knob
Material: High-resilience polypropylene based (PP) technopolymer, coated with thermoplastic elastomer (TPE) "soft-touch" chemically bonded, hardness 70 Shore A. Resistant to solvents, oils, greases and other chemical agents.
The coating material is certified according to FDA (U.S. Food and Drug administration).
Colour: Black, matte finish.
Centre cap: Polypropylene based technopolymer (PP), in the six standard colours, matte finish. On request and for sufficient quantities, it can be supplied in other colours or with customised graphic symbols, marks or writings.
Standard execution: Brass boss, threaded blind hole.
Colour codes centre caps:
C9 = Black RAL9005
C2 = Orange RAL2004
C3 = Grey RAL7035
C4 = Yellow RAL1021
C5 = Blue RAL5024
C6 = Red RAL3000
Elesa+Ganter VCT.p SOFT Lobe knob
Material: High-resilience polypropylene based (PP) technopolymer, coated with thermoplastic elastomer (TPE) "soft-touch" chemically bonded, hardness 70 Shore A. Resistant to solvents, oils, greases and other chemical agents.
The coating material is certified according to FDA (U.S. Food and Drug administration).
Colour: Black, matte finish.
Centre cap: Polypropylene based technopolymer (PP), in the six standard colours, matte finish. On request and for sufficient quantities, it can be supplied in other colours or with customised graphic symbols, marks or writings.
Standard execution: Zinc-plated steel threaded stud with chamfered flat end as in UNI 947 : ISO 4753 (see Technical Data ).
Colour codes centre caps:
C9 = Black RAL9005
C2 = Orange RAL2004
C3 = Grey RAL7035
C4 = Yellow RAL1021
C5 = Blue RAL5024
C6 = Red RAL3000
Elesa+Ganter VC.692 Lobe knob
Material: Glass-fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, matte finish.
Standard execution: Brass boss, threaded blind hole.
Elesa+Ganter VC.692 p Lobe knob
Materiale: Glass-fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, matte finish.
Standard execution: Zinc-plated steel threaded stud, chamfered flat end according to UNI 947 : ISO 4753 (see Technical Data ).
Elesa+Ganter VC.692-CLEAN Lobe knob
Glass-fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Colour: White similar to RAL 9002, matte finish.
Assembly: AISI 303 stainless steel boss, tapped blind hole.
Elesa+Ganter VC.692 Chrome-plated lobe knob
Material: Glass-fibre reinforced polyamide based (PA) technopolymer, chrome-plated, semi-glossy finish.
Assembly: Brass boss, tapped blind hole.
Elesa+Ganter VC.692-SST Lobe knob with stainless steel threaded blind hole.
Material: Glass-fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, matte finish.
Standard execution: AISI 303 stainless steel boss, threaded blind hole.
Elesa+Ganter VC.692-SST-p Lobe knob with thread stud in stainless steel
Material: Glass-fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, matte finish.
Standard execution: AISI 303 stainless steel threaded stud, chamfered flat end according to UNI 947 : ISO 4753 (see Technical Data ).
Elesa+Ganter VC.192 Lobe knob
Material: Phenolic based (PF) Duroplast. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, glossy finish.
Assembly:
- Execution A: black-oxide steel boss, plain blind hole.
- Execution B: brass boss, plain or tapped blind hole.
Elesa+Ganter VC.192 p Lobe knob with thread
Material: Phenolic based (PF) Duroplast. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, glossy finish.
Zinc-plated steel threaded stud, chamfered flat end according to UNI 947 : ISO 4753 (see Technical Data ).
Elesa+Ganter VC.192 SST Lobe knob
Material: Phenolic based (PF) Duroplast. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, glossy finish.
Assembly: AISI 303 stainless steel boss, tapped blind hole.
Elesa+Ganter VC.192 SST-p Lobe knob
Material: Phenolic based (PF) Duroplast. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, glossy finish.
Assembly: AISI 303 stainless steel threaded stud.
Elesa+Ganter VC.253 Lobe knob shortened series
Material: Phenolic based (PF) Duroplast. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, glossy finish.
Assembly: Black-oxide steel boss, tapped through hole.
Elesa+Ganter VC.254 Lobe knob
Material: Phenolic based (PF) Duroplast. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, glossy finish.
Assembly: Brass boss, tapped through hole and large metal locking face.
Conformity
UNI 6960-71 type B with through hole.
Elesa+Ganter GN 5334 Lobe knob
Material: AISI 304 stainless steel, sandblasted matte finish.
Assembly
- Type C: with butt-welded hub, H7 reamed blind hole.
- Type E: with butt-welded hub, tapped blind hole.
For fixing GN 5334 on shafts by a grub screw see Technical Data.
Elesa+Ganter GN 5334 Lobe knob
Material: AISI 304 stainless steel, sandblasted matte finish.
Elesa+Ganter GN 5335 Lobe knob
Material: AISI 304 stainless steel.
Finish
- sandblasted, matte finish.
- Version PL: polished.
Assembly
- Type C: hub, H7 reamed blind hole.
- Type E: hub, tapped blind hole.
- Type D: hub, tapped through hole.
For fixing GN 5335 on shafts by a grub screw see Technical Data.
Elesa+Ganter GN 5336 Lobe knob
Material: Cast aluminium.
- Execution PL: with deburred and mirror-polished finish.
- Execution MT: with sandblasted matte finish.
Assembly
- Execution A: hub not drilled, only with matte finish.
- Execution C: hub, H7 reamed blind hole.
- Execution E: hub, tapped blind hole.
- Execution D: hub, tapped through hole.
For fixing GN 5336 on shafts by a grub screw see Technical Data.
Elesa+Ganter DIN 6335 Lobe knob
Material
- cast aluminium with matte finish (version MT)
- cast iron.
Assembly
- Type B: hub, H7 reamed through hole.
- Type C: hub, H7 reamed blind hole.
- Type D: hub, tapped through hole.
- Type E: hub, tapped blind hole.
Elesa+Ganter DIN 6336 Lobe knob
Material
- cast aluminium with matte finish (version MT)
- cast aluminium with deburred and mirror polished finish (version PL).
- cast iron.
Assembly
- Type B: hub, H7 reamed through hole.
- Type C: hub, H7 reamed blind hole.
- Type D: hub, tapped through hole.
- Type E: hub, tapped blind hole.
Elesa+Ganter GN 6335.9 Star knob high clamping force
Knob: Polyamide-based (PA) reinforced technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, matte finish.
Threaded insert: Black-oxide nitrided steel.
Axial ball bearing: Hardened steel.
Elesa+Ganter Security lobe knob VLS.
Lobe solid cap: Glass-fibre reinforced polyamide based (PA) technopolymer with security anti-intrusion-profiled key slot. Resistant to solvents, oils, greases and other chemical agents.
Flange: Technopolymer, ultrasonically welded.
Colour: Black, matte finish.
Clamping element: Acetal resin based (POM) technopolymer.
Assembly: Brass boss, tapped blind hole.
Elesa+Ganter VLS.SST-p Security lobe knob, stainless steel
Lobe solid cap: Glass-fibre reinforced polyamide based (PA) technopolymer with security anti-intrusion-profiled key slot. Resistant to solvents, oils, greases and other chemical agents.
Flange: Technopolymer, ultrasonically welded.
Colour: Black, matte finish.
Clamping element: Acetal resin based (POM) technopolymer.
Assembly: AISI 303 stainless steel threaded stud, chamfered flat end according to UNI 947 : ISO 4753 (see Technical Data).
Elesa+Ganter GN 5337.3 Safety star knob
Knob Plastic: Technopolymer (Polyamide PA) glass fibre reinforced, temperature resistant up to 130 °C, black, matt finish
Threaded bush / Threaded stud
- ST: Steel, blackened
- NI: Stainless Steel AISI 303
Elesa+Ganter VLSK Security lobe knob with lock
Material: Glass-fibre reinforced polyamide based (PA) technopolymer with slot for codified key lock. Resistant to solvents, oils, greases and other chemical agents.
Central closing cap: Technopolymer black colour.
Flange: Technopolymer, ultrasonically welded.
Colour: Black, matte finish.
Clamping element: Glass-fibre reinforced polyamide based (PA) SUPER-tecnopolymer.
PR Elesa+Ganter_ SUPER-Technopolymer.
Elesa+Ganter VCRT. Lobe knob with square hole
Material: Glass reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, matte finish.
Assembly: Square through hole with brass reinforcement. On request and for sufficient quantities, it can be supplied with square through hole without brass reinforcement.
Elesa+Ganter VCR.192 Lobe knob with square hole
Material: Phenolic based (PF) Duroplast. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, glossy finish.
Assembly: Square through hole with brass reinforcement.
Elesa+Ganter VZ. Knurled knobs with square hole
Material: Phenolic based (PF) Duroplast. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, glossy finish.
Standard execution: Square through hole with brass reinforcement.
Elesa+Ganter VLT. Lobe knob
Material: Glass-fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, matte finish.
Closing cap: Polypropylene based (PP) technopolymer, RAL 2004 orange colour, glossy finish with matte central surface, snap-in mounting.
Standard executions
- VTL-B: brass boss, threaded blind hole.
- VTL-p: zinc-plated steel threaded stud, chamfered flat end according to UNI 947: ISO 4753 (see Technical Data).
Elesa+Ganter ELK. Lobe knob
Material: Glass-fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Colour: Grey-black, matte finish.
Assembly
- Execution A: black-oxide steel boss, H9 reamed blind hole.
- Execution B: brass boss, tapped blind hole.
Cap: Technopolymer in Ergostyle colours, matte finish. Ultrasonically welded to the body of the knob.
Cap colours:
C1: Black RAL 7021
C2: Orange RAL2004
C3: Grey RAL7035
C4: Yellow RAL7035
C5: Light blue RAL5024
C6: Red RAL3000
Elesa+Ganter ELK.p Lobe knob
Material: Glass-fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Colour: Grey-black, matte finish.
Assembly: Zinc-plated steel threaded stud, chamfered flat end according to UNI 947 : ISO 4753 (see Technical Data ).
Cap: Technopolymer in Ergostyle colours, matte finish. Ultrasonically welded to the body of the knob.
Cap colours:
C1: Black RAL 7021
C2: Orange RAL2004
C3: Grey RAL7035
C4: Yellow RAL7035
C5: Light blue RAL5024
C6: Red RAL3000
Elesa+Ganter ELK.FP Lobe knob
Material: Glass-fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Colour: Grey-black, matte finish.
Assembly: Black-oxide steel boss, H7 reamed through hole.
Cap with through hole: Technopolymer in Ergostyle colours, matte finish. Ultrasonically welded to the body of the knob.
Coluorcodes caps:
C1: Black RAL 7021
C2: Orange RAL2004
C3: Grey RAL7035
C4: Yellow RAL1021
C5: Light Blue RAL5024
C6: Red RAL3000
Elesa+Ganter VL.140 Lobe knob
Material: Phenolic based (PF) Duroplast. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, glossy finish.
Assembl:
Black-oxide steel hub, pre-drilled blind hole.
Elesa+Ganter VL.155 Lobe knob
Material: Phenolic based (PF) Duroplast. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, glossy finish.
Assembly
- Execution A: black-oxide steel boss, plain blind hole.
- Execution B: brass boss, plain or tapped blind hole.
Elesa+Ganter VL.155 p lobe knob
Material: Phenolic based (PF) Duroplast. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, glossy finish.
Assembly: Zinc-plated steel threaded stud, chamfered flat end according to UNI 947 : ISO 4753 (see Technical Data ).
Elesa+Ganter VL.640 FP Lobe knob
Material: glass reinforced polyamide based (PA) technopolymer.
Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, glossy finish.
Standard executions:
VL.640 FP-A: black-oxide steel hub available in different executions:
- not drilled.
- H7 reamed pass-through hole.
- 6H threaded pass-through hole.
VL.640 FP-B: brass hub, not drilled.
Elesa+Ganter VH.153 lobe knob
Material: Phenolic based (PF) Duroplast. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, glossy finish.
Assembly
- Execution A: black-oxide steel boss, plain blind hole.
- Execution B: brass boss, plain or tapped blind hole.
Elesa+Ganter VH.153 p Lobe knob
Material: Phenolic based (PF) Duroplast. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, glossy finish.
Assembly: Zinc-plated steel threaded stud, chamfered flat end according to UNI 947 : ISO 4753 (see Technical Data ).
Elesa+Ganter VTR. Lock knobs
Material: Polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, orange, glossy finish.
Plate: Matte anodised aluminium.
Assembly: Brass boss, tapped blind hole.
Elesa+Ganter VTR.p Lock knob with thread
Material: Polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, glossy finish.
Plate: Matte anodised aluminium.
Assembly: Zinc-plated steel threaded stud, chamfered flat end according to UNI 947 : ISO 4753 (see Technical Data ).
Elesa+Ganter VTR.N Lock knob
Material: Polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, glossy finish.
Assembly: Square hole.
Elesa+Ganter VTR.FP Lock knob
Material: Polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, glossy finish.
Assembly: Brass boss, tapped through hole.
Elesa+Ganter GN 5339.5 Lock knob in stainless steel
Material: AISI 303 stainless steel.
Standardversion
- MT: sandblasted matte finish.
- PL: polished.
Assembly
- Type E: hub, tapped blind hole, highly polished.
- Type D: hub, tapped through hole, highly polished.
- Type C: hub, H7 reamed blind hole.
Elesa+Ganter GN 420 Knurled nut
Material: Technopolymer (Polyamide PA), black, shiny finish
Bush: Steel zinc plated, blue passivated
Elesa+Ganter GN 420-NI Knurled nut
Plastic: Technopolymer (Polyamide PA) black, shiny finish
Bush: Stainless Steel AISI 303
Elesa+Ganter GN 421 knurled screw
Material: Technopolymer (Polyamide PA)
black, shiny finish
Threaded bolt: Steel zinc plated, blue passivated
Elesa+Ganter GN 421-NI knurled screw
Material: Technopolymer (Polyamide PA)
black, shiny finish
Threaded bolt: Stainless Steel AISI 304
Elesa+Ganter BT. Fluted grip knob
Material: Polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, matte finish.
Standard execution: Brass boss, threaded blind hole.
Elesa+Ganter BT.p Fluted grip knob
Material: Polyamide based (PA) technopolymer. Resistant to solvents, olis, greases and other chemical agents.
Colour: Black, matte finish.
Assembly: Zinc-plated steel threaded stud, chamfered flat end according to UNI 947 : ISO 4753 (see Technical Data).
Elesa+Ganter BT.FP Fluted grip knob
Material: Polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, matte finish.
Assembly: Brass boss, tapped through hole.
Elesa+Ganter MBT. Color Diamond cut knurled knob
Material: High-resilience polypropylene based (PP) technopolymer. Resistant to solvents, oils, greases and other chemical agents. With coloured centre cap
Technopolymer, matte finish.
Colour: Black, matte finish.
Brass boss, plain or threaded blind hole.
To order, add the index of the desired colour (C9, ..., C6) to the code and the description.
On request and for sufficient quantities, it can be supplied in other colours or with customised graphic symbols, marks or writings.
Color codes centre cap:
C9 = Black
C2 = Orange
C3 = Grey
C4 = Yellow
C5 = Blue
C6 = Red
Elesa+Ganter MBT.p Color Diamond cut knurled knob with coloured centre cap
Material: High-resilience polypropylene based (PP) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, matte finish.
Coloured centre cap: Technopolymer, matte finish.
To order, add the index of the desired colour (C9, ..., C6) to the code and the description.
On request and for sufficient quantities, it can be supplied in other colours or with customised graphic symbols, marks or writings.
Standard execution
Zinc-plated steel threaded stud, chamfered flat end according to UNI 947 : ISO 4753 (see Technical Data).
Color codes centre cap:
C9 = Black
C2 = Orange
C3 = Grey
C4 = Yellow
C5 = Blue
C6 = Red
Elesa+Ganter MBT.p SOFT Fluted grip knob
Material: High resilience polypropylene based (PP) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Fluted rim: "Soft-touch" thermoplastic elastomer (TPE) chemically bonded, hardness 70 Shore A.
Colour: Black, matte finish.
Standard execution: Zinc-plated steel threaded stud, chamfered flat end according to UNI 947 : ISO 4753 (see Technical Data).
Elesa+Ganter MBT.SOFT Fluted grip knob
Material: High-resilience polypropylene based (PP) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Fluted rim: "Soft-touch" thermoplastic elastomer (TPE) chemically bonded, hardness 70 Shore A. The coating material is certified according to FDA (U.S. Food and Drug administration).
Colour: Black, matte finish.
Standard execution: Brass boss, threaded blind hole.
Elesa+Ganter BT-SST Fluted grip knob
Material: Polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, matte finish.
Assembly: AISI 303 stainless steel boss, tapped blind hole.
Elesa+Ganter BT-SST-p Fluted grip knob
Material: Polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, matte finish.
Assembly: AISI 303 stainless steel threaded stud, chamfered flat end according to UNI 947 : ISO 4753 (see Techincal Data).
Elesa+Ganter BT.FP-ESD Fluted grip knob
Material: Polyamide based (PA) special antistatic technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, matte finish.
Assembly: Brass boss, tapped through hole.
Elesa+Ganter BT-ESD Fluted grip knob
Material: Polyamide based (PA) special antistatic technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, matte finish.
Assembly: Brass boss, tapped blind hole.
Elesa+Ganter BT.p-ESD Fluted grip knob
Material: Polyamide based (PA) special antistatic technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, matte finish.
Assembly: Zinc-plated steel threaded stud, chamfered flat end according to UNI 947 : ISO 4753 (see Technical Data).
Elesa+Ganter B.193 FP Knurled grip knob
Material: Phenolic based (PF) Duroplast. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, glossy finish.
Assembly: Brass boss, tapped through hole.
Elesa+Ganter B.193 Knurled grip knob
Material: Phenolic based (PF) Duroplast. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, glossy finish.
Standard execution: Brass boss, tapped blind hole.
Elesa+Ganter B.193 p Knurled grip knob
Material: Phenolic based (PF) Duroplast. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, glossy finish.
Assembly: Zinc-plated steel threaded stud, chamfered flat end according to UNI 947 : ISO 4753 (see Technical Data).
Elesa+Ganter B.193-SST Knurled grip knob
Material:
Knob: Phenolic based (PF) Duroplast. Resistant to solvents, oils, greases and other chemical agents.
Colour:Black, glossy finish.
Standard execution: AISI 303 stainless steel boss, tapped blind hole.
Elesa+Ganter B.193-SST-p knurled grip knob
Material: Phenolic based (PF) Duroplast. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, glossy finish.
Assembly: AISI 303 stainless steel threaded stud, chamfered flat end according to UNI 947 : ISO 4753 (see Technical Data ).
Elesa+Ganter B.259 knurled grip knob
Material: Phenolic based (PF) Duroplast. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, glossy finish.
Assembly: Brass boss, tapped blind hole.
Elesa+Ganter B.259 p knurled grip knob
Material: Phenolic based (PF) Duroplast. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, glossy finish.
Assembly: Zinc-plated steel threaded stud, chamfered flat end according to UNI 947 : ISO 4753 (see Technical Data ).
Elesa+Ganter B.259-CLEAN knurled grip knob
Material: Painted phenolic based (PF) Duroplast.
Colour: White similar to RAL 9002, glossy finish.
Assembly: AISI 303 stainless steel boss, tapped blind hole.
Elesa+Ganter B.220 Knurled grip knob
Material: Phenolic based (PF) Duroplast. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, glossy finish.
Assembly: Black-oxide steel hub, plain blind hole.
Elesa+Ganter DIN 6303 knurled grip knob
Material: Black-oxide steel.
Assembly: Tapped through hole (execution A).
Tapped through hole with semi-machined threaded hole (execution B).
Elesa+Ganter DIN 6303-NI knurled grip knob
Material: AISI 303 stainless steel, sandblasted matte finish.
Assembly
Tapped through hole (execution A).
Tapped through hole with semi-machined threaded hole (execution B).
Elesa+Ganter DIN 464 knurled grip knob with threaded pin
Material: Turned black-oxide steel.
Assembly: Threaded pin.
Elesa+Ganter DIN 464-NI knurled grip knob with threaded pin
Material: AISI 303 stainless steel, sandblasted matte finish.
Assembly: Threaded pin.
Elesa+Ganter DIN 466 knurled grip knob
Material: Turned black-oxide steel.
Assembly: Hub, tapped through hole.
Elesa+Ganter DIN 466-NI knurled grip knob in stainless steel
Material: AISI 303 stainless steel, sandblasted matte finish.
Assembly: Hub, tapped through hole.
Elesa+Ganter DIN 653 knurled grip knobs with threaded pin.
Material: Turned black-oxide steel.
Assembly: Threaded pin.
Elesa+Ganter DIN 653 knurled grip knob with threaded pin
Material: AISI 303 stainless steel, sandblasted matte finish.
Assembly: Threaded pin.
Elesa+Ganter GN 653.2 Knurled screw
Knurled screws GN 653.2 can be used for to prevent loss of the thumb screw, due to the d4 recessed portion of the stud.
Specification version ST:
Made from steel
- Tensile strength class 5 (500N/mm2)
- visible face fine turned
- black oxide finish
Elesa+Ganter DIN 467 knurled grip knob
Material: Turned black-oxide steel.
Assembly: Tapped through hole.
Elesa+Ganter DIN 467 knurled grip knob
Material: AISI 303 stainless steel, sandblasted matte finish.
Assembly: Tapped through hole.
Elesa+Ganter MCT. fluted grip knob
Material: Polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, matte finish.
Closing cap: Polypropylene based (PP) technopolymer, orange or black colour, glossy finish with matte central surface, snap-in mounting.
Standard execution: Assembly by means of hexagon head screws or standard lock nuts (not supplied) to put in place inside the knob by pressing.
Elesa+Ganter EWN.FP wing nut
Material: Glass-fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Colour: Grey-black, matte finish.
Assembly: brass boss, tapped through hole, without cap.
Elesa+Ganter EWN. wing nut
Material: Glass-fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Colour: Grey-black, matte finish.
Assembly: brass boss, tapped through hole, with cap.
Cap for EWN.: Technopolymer in Ergostyle colours, matte finish; supplied assembled, press-fit assembly, removable by a screwdriver.
Available also as accessory sold separately (see caps table).
Cap colours:
C1: Black RAL 7021
C2: Orange RAL2004
C3: Grey RAL7035
C4: Yellow RAL7035
C5: Light blue RAL5024
C6: Red RAL3000
Elesa+Ganter EWN.p wing screw
Material: Glass-fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Colour: Grey-black, matte finish.
Assembly: Zinc-plated steel threaded stud, chamfered flat end according to UNI 947 : ISO 4753 (see Technical Data ).
Cap: Technopolymer in Ergostyle colours, matte finish; supplied assembled, press-fit assembly, removable by a screwdriver.
Available also as accessory sold separately (see caps table).
Cap colours:
C1: Black RAL 7021
C2: Orange RAL2004
C3: Grey RAL7035
C4: Yellow RAL7035
C5: Light blue RAL5024
C6: Red RAL3000
Elesa+Ganter EWN.SST-FP wing nut
Material: Glass-fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Colour: Grey-black, matte finish.
Assembly: AISI 303 stainless steel boss, tapped through hole, without cap.
Elesa+Ganter EWN.SST wing nut with cap
Material: Glass-fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Colour: Grey-black, matte finish.
Assembly: AISI 303 stainless steel boss, tapped through hole, with cap.
Cap for EWN.SST: Technopolymer in Ergostyle colours, matte finish; supplied assembled, press-fit assembly, removable by a screwdriver.
Available also as accessory sold separately (see caps table).
Cap colours:
C1: Black RAL 7021
C2: Orange RAL2004
C3: Grey RAL7035
C4: Yellow RAL7035
C5: Light blue RAL5024
C6: Red RAL3000
Elesa+Ganter EWN.SST-p wing screw
Material: Glass-fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Colour: Grey-black, matte finish.
Cap: Technopolymer in Ergostyle colours, matte finish; supplied assembled, press-fit assembly, removable by a screwdriver.
Available also as accessory sold separately (see caps table).
Standard execution: AISI 303 stainless steel threaded stud, chamfered flat end according to UNI 947 : ISO 4753 (see Technical Data ).
Cap colours:
C1: Black RAL 7021
C2: Orange RAL2004
C3: Grey RAL7035
C4: Yellow RAL7035
C5: Light blue RAL5024
C6: Red RAL3000
Elesa+Ganter ESN. Single wing nut with coloured cap
Material: Glass-fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Colour: Grey-black, matte finish.
Assembly: Brass boss, tapped through hole.
Cap: Technopolymer in Ergostyle colours, matte finish; supplied assembled, press-fit assembly, removable by a screwdriver.
Available also as accessory sold separately (see caps table).
Cap colours:
C1: Black RAL 7021
C2: Orange RAL2004
C3: Grey RAL7035
C4: Yellow RAL7035
C5: Light blue RAL5024
C6: Red RAL3000
Elesa+Ganter CWN.FP Wing nut
Material: Glass-fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, matte finish.
Assembly: Brass boss, tapped through hole.
Elesa+Ganter CWN. Wing nut
Material: Glass-fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, matte finish.
Assembly: Brass boss, tapped blind hole.
Elesa+Ganter CWN.p wing nut
Material: Glass-fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, matte finish.
Assembly: Zinc-plated steel threaded stud, chamfered flat end according to UNI 947 : ISO 4753 (see Technical Data).
Elesa+Ganter GN 731 Wing nut
Material: Stainless steel with sand-blasted finish.
Mounting hole:
- Type E: tapped blind hole.
- Type D: tapped through hole.
Elesa+Ganter GN 431 Wing knob
Material: AISI 316L sintered stainless steel, sandblasted matte finish.
Assembly: AISI 304 stainless steel threaded pin, screwed and set in the body with a lock pin.
Elesa+Ganter GN 432 Wing knob
Material: AISI 316L sintered stainless steel, sandblasted matte finish.
Assembly: Tapped blind hole.
Elesa+Ganter CT.476 FP wing knob
Material: Glass-fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, matte finish.
Standard execution: Brass boss, threaded pass-through hole.
Elesa+Ganter CT.476 wing knob
Material: Glass-fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, matte finish.
Standard execution: Brass boss, threaded blind hole.
Elesa+Ganter CT.476 p wing knob
Material: Glass-fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, matte finish.
Standard execution: Zinc-plated steel threaded stud, chamfered flat end according to UNI 947.
Elesa+Ganter CT.476-SST-p wing knob
Material: Glass-fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, matte finish.
Assembly: AISI 303 stainless steel threaded stud, chamfered flat end according to UNI 947.
Elesa+Ganter CTL.476 wing knob
Material: Glass-fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, matte finish.
Standard execution: Brass boss, threaded blind hole.
Elesa+Ganter CTL.476 p Wing knob
Material: Glass-fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, matte finish.
Standard execution: Zinc-plated steel threaded stud, chamfered flat end according to UNI 947.
Elesa+Ganter GN 433 wing knob in stainless steel
Material: AISI CF-8 stainless steel (precision casting), sandblasted matte finish.
Assembly: Threaded pin.
Elesa+Ganter GN 434 Wing knob in stainless steel
Material: AISI CF-8 stainless steel (precision casting), sandblasted matte finish.
Assembly: Tapped blind hole.
Elesa+Ganter GN 7336-NI Knurled knob with threaded pin.
Material: Plastic, polyamide based (PA) technopolymer, glas fibre reinforced, temperature resistant up to 130 °C.
Threaded pin: AISI 304 stainless steel NI.
Cover cap: Light grey, matte.
Elesa+Ganter GN 7336-NI Knurled knob
Material: Plastic, polyamide based (PA) technopolymer, glas fibre reinforced, temperature resistant up to 130 °C.
Threaded bush: AISI 304 stainless steel NI.
Cover cap: Light grey, matte.
Elesa+Ganter GN 835 Wing screw in stainless steel
Material: Precision casting AISI CF-8 stainless steel, sandblasted matte finish.
Assembly: Threaded pin.
Elesa+Ganter GN 653.10 Flat knurled thumb screw in steel or GN 653.10-NI in stainless steel
Material:
- ST: Turned black-oxide steel, visible face fine turned.
- NI: AISI 304 stainless steel, sandblasted matte finish, visible face fine turned.
Assembly: Threaded pin.
Pivot:
- Version MS: brass.
- Version KU: plastic, polyacetal (POM).
Elesa+Ganter GN 7336.5 Knurled knob
Material: Plastic, polyamide based (PA) techno polymer, glass fiber reinforced, temperature resistant up to 130 ° C.
Threaded Stud: Stainless steel AISI 304 A2.
Protective shield: Light gray, matte.
Standard versions available
- Type MS: Brass.
- Type KU: Plastic. (POM)
- Type ZK: spherical tap
Elesa+Ganter GN 5345 Stainless Steel-Three-star knob
Material: AISI 303 Stainless Steel, matt-blasted.
Standard versions:
- Type A: casting only.
- Type E: with threaded blind bore.
- Type D: with threaded through bore.
- Type C: with plain blind bore H7.
Special execution on request.
Stainless Steel-Three-star knobs GN 5345 have a smooth and sealed surface. They are particularly suitable for use where hygiene requirements are high. Their shape allows relatively high torques to be applied.
Elesa+Ganter GN 5345.4 Three-star knob
Materiaal: AISI 316L (A4) Stainless Steel, matt-blasted.
Standard versions available:
- Type A: casting only.
- Type E: with threaded blind bore.
- Type D: with threaded through bore.
- Type C: with plain blind bore H7.
Special execution on request.
Stainless Steel-Three-star knobs GN 5345.4 have a smooth and sealed surface. They are particularly suitable for use where hygiene requirements are high. Their shape allows relatively high torques to be applied.
Elesa-Ganter VC.692-SST-p-P Lobe knob with bolt
Material: Glass-fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, matte finish.
Standard executions:
-VC.692-SST-p-PO: AISI 303 stainless steel threaded stud, chamfered end with acetal resin (POM) bolt.
-VC.692-SST-p-PB: AISI 303 stainless steel threaded stud, chamfered end with brass bolt.
Elesa-Ganter DIN 6335-NI Stainless steel star knob
Material: AISI CF-8 stainless steel, sandblasted matte finsih.
Assembly:
- Type A: casting only (unmachined).
- Type D: with threaded through bore.
- Type E: with threaded blind bore.
Elesa-Ganter VCTS-Z lobe knob
Knob: Glass-fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Built-in zinc alloy toothed insert for coupling to the metal clamping element.
Colour: Black, matte finish.
Centre cap: Black technopolymer centre cap. On request and for sufficient quantities, it can be supplied in yellow RAL 1021 (safety) or in other colours, with customised graphic symbols, marks or writings.
Clamping element: Black-oxide steel with threaded bore and toothed element for coupling to the built-in zinc alloy insert, black-oxide steel retaining screw and AISI 302 stainless steel return spring.
Elesa-Ganter VCTS-Z-p Adjustable lobe knob with push action
Knob: Glass-fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Built-in zinc alloy toothed insert for coupling to the metal clamping element.
Colour: Black, matte finish.
Centre cap: Black technopolymer centre cap. On request and for sufficient quantities, it can be supplied in yellow RAL 1021 (safety) or in other colours, with customised graphic symbols, marks or writings.
Clamping element: Black-oxide steel with toothed element for coupling to the built-in zinc alloy insert, black-oxide steel retaining screw and AISI 302 stainless steel return spring.
Elesa-Ganter VCTS-SST Adjustable lobe knob with push action
Knob: Glass-fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Built-in zinc alloy toothed insert for coupling to the metal clamping element.
Colour: Black, matte finish.
Centre cap: Black technopolymer centre cap. On request and for sufficient quantities, it can be supplied in yellow RAL 1021 (safety) or in other colours, with customised graphic symbols, marks or writings.
Clamping element: AISI 303 stainless steel with threaded bore and toothed element for coupling to the built-in zinc alloy insert, stainless steel retaining screw and AISI 302 stainless steel return spring.
Elesa-Ganter VCTS-Z-SST-p Adjustable lobe knob with push action
Knob: Glass-fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Built-in zinc alloy toothed insert for coupling to the metal clamping element.
Colour: Black, matte finish.
Centre cap: Black technopolymer centre cap. On request and for sufficient quantities, it can be supplied in yellow RAL 1021 (safety) or in other colours, with customised graphic symbols, marks or writings.
Clamping element: AISI 303 stainless steel with toothed element for coupling to the built-in zinc alloy insert, stainless steel retaining screw and AISI 302 stainless steel return spring.
Elesa-Ganter VCRT.FP Lobe knob with threaded pass-through hole.
Material: Glass fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, matte finish.
Standard execution: Brass boss, threaded pass-through hole.
Elesa-Ganter VCR.372 lobe knob
Material: Phenolic based (PF) Duroplast. Resistant to solvents, oils, greases and other chemical agents.
Colour: Black, glossy finish.
Assembly: Square through hole with brass reinforcement.
Elesa-Ganter GN 535 knurled screw in stainless steel
Material: AISI 304 stainless steel.
- Version MT: matt blasted.
- Version PL: polished.
Assembly: Threaded pin.
Elesa-Ganter GN 536 knurled nut
Material: AISI 304 stainless steel.
- Version MT: matt blasted.
- Version PL: polished.
Assembly: Tapped blind hole.
Elesa-Ganter EWN-SST-p-P wing screw with bolt
Material: Glass-fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
Colour: Grey-black, matte finish.
Cap: Technopolymer in Ergostyle colours, matte finish; supplied assembled, press-fit assembly, removable by a screwdriver.
Available also as accessory sold separately (see table).
Standard executions:
-EWN-SST-p-PO: AISI 303 stainless steel threaded stud, chamfered end with acetal resin (POM) bolt.
-EWN-SST-p-PB: AISI 303 stainless steel threaded stud, chamfered end with brass bolt.
Elesa-Ganter EWNM-SST wing screw in stainless steel
Material: AISI 304 stainless steel, sandblasted matte finish.
Standard executions:
- EWNM-SST: threaded blind hole.
- EWNM-SST-FP: threaded pass-through hole.
- EWNM-SST-p: threaded pin.
Elesa-Ganter GN 834 wing nut in stainless steel
Material: Precision casting AISI CF-8 stainless steel, sandblasted matte finish.
Standard executions:
- Type D: tapped through hole.
- Type E: tapped blind hole.
Elesa-Ganter GN 7336 Knurled knob in stainless steel with bore.
Material: Plastic, polyamide based (PA) technopolymer, glas fibre reinforced, temperature resistant up to 130 °C.
Threaded bush: AISI 304 stainless steeI.
Cover cap in light grey plastic.
Elesa-Ganter GN 7336 Knurled knob in stainless steel with treaded pin.
Material. Plastic, polyamide based (PA) technopolymer, glas fibre reinforced, temperature resistant up to 130 °C.
Threaded pin: AISI 304 stainless steel NI.
Cover cap: Light grey, matte.
Stainless Steel-Hand knobs GN 6335 satisfy the dimensions of the DIN 6335 but differ in terms of their non-scooping geometry, which makes cleaning easier and helps prevent possible build-up of dirt.
They are suitable for areas with special hygiene requirements and, thanks to the material used, for applications in highly corrosive environments.
Types:
- Type D: with threaded through bore
- Type E: with threaded blind bore
- Stainless Steel precision casting A4
Material:
- Stainless steel AISI 316, polished PL
Elesa-Ganter GN 6335.5 Star knob
Threaded bolt: AISI 303 stainless steel.
Standard versions available:
- Version AM: Star knob DIN 6335 Aluminium (AL), matt (ground).
- Version AP: Star knob DIN 6335 Aluminium (AL), polished.
Assembly: The threaded bolt is screwed in and secured by a crossdowel.
Elesa-Ganter GN 6335.5-ES star knob
Star knob: AISI CF-8 stainless steel ES, sandblasted matte finish.
Threaded bolt: AISI 303 stainless steel.
Assembly: The threaded bolt is screwed in and secured by a crossdowel.
Elesa-Ganter GN 6336.5 lobe knob with threaded bolt in stainless steel
Threaded bolt: AISI 303 stainless steel.
Standard versions available:
- Version AM: Star knob DIN 6335 Aluminium (AL), matt (ground).
- Version AP: Star knob DIN 6335 Aluminium (AL), polished.
Assembly: The threaded bolt is screwed in and secured by a crossdowel.
Elesa-Ganter GN 6336.5-ES Lobe knob
Star knob: AISI CF-8 stainless steel ES, sandblasted matte finish.
Threaded bolt: AISI 303 stainless steel.
Assembly: The threaded bolt is screwed in and secured by a crossdowel.
Elesa-Ganter GN 6335.4-SG Star knob
Star knob: Cast iron.
Threaded bolt: Blackened.
Assembly: The threaded bolt is screwed in and secured by a crossdowel.
Elesa-Ganter GN 6336.4-SG Star knob
Material: Cast iron.
Threaded bolt: Blackened.
Assembly: The threaded bolt is screwed in and secured by a crossdowel.
Elesa-Ganter GN 5334.4 Stanless steel star knob
Material: AISI 316L (A4) stainless steel, hub welded, matt shot-blasted.
Standard versions available:
- Type E: with threaded blind bore.
- Type C: with blind bore H7.
Elesa-Ganter GN 5334.4 Stainless steel star knob with thread
Material: AISI 316L (A4) stainless steel, hub welded, matt shot-blasted.
Elesa-Ganter GN 5335.4 Lobe knob in stainless steel
Types:
- Type A: without bore
- Type E: with threaded blind bore
- Type D: with threaded through bore
- Type C: with plain blind bore H7
Material: Stainless Steel AISI 316L (A4), matt shot-blasted
Elesa+Ganter GN 653.2-NI Knurled screw
Made from Stainless Steel NI, AISI 303
- visible face fine turned
- matt shot-blasted
Elesa-Ganter VTT lobe knob
Material: Glass-fibre reinforced polyamide based (PA) technopolymer, black colour, matte finish.
Standard executions
- VTT:ﾠ brass boss, threaded blind hole.
- VTT-SST:ﾠ AISI 304 stainless steel boss, threaded blind hole.
- VTT-p: ﾠzinc-plated steel threaded stud, chamfered flat end according to UNI 947 : ISO 4753
- VTT-SST-p: AISI 304 stainless steel threaded stud, chamfered flat end according to UNI 947 : ISO 4753
Elesa-Ganter VTT-CLEAN Lobe knob
Material: Glass-fibre reinforced polyamide based (PA) technopolymer, white colour similar to RAL 9002, matte finish.
Standard executions:
- VTT-CLEAN: AISI 304 stainless steel boss, threaded blind hole.
- VTT-p-CLEAN: AISI 304 stainless steel threaded stud, chamfered flat end according to UNI 947 : ISO 4753
E+G VTT-SST-VD Lobe knob in visually detectable technopolymer
Glass-fibre reinforced polyamide based (PA) technopolymer, RAL 5001 blue colour, matte finish.
Produced from FDA compliant raw material (FDA CFR.21 and EU 10/2011).
The RAL 5005 blue colour is easily visible in case of accidental food contamination.
This makes it suitable for applications in the food and pharmaceutical industries.
Also available in metal detectable version MD
Glass-fibre reinforced polyamide based (PA) technopolymer, RAL 5001 blue colour, matte finish.
Produced from FDA compliant raw material (FDA CFR.21 and EU 10/2011).
The special technopolymer contains additives detectable by means of metal detectors.
Built-in zinc alloy toothed insert for coupling to the metal clamping element.
The RAL 5001 blue colour is easily visible in case of accidental food contamination. Furthermore the material additives are metal detectable at a cubic particle size of 5 mm per side.
E+G VTT-SST-SAN lobe knob in technopolymer with antibacterial protection.
Glass-fibre reinforced polyamide based (PA) with silver ion additive on an inorganic base, RAL 7021 grey-black colour (C1) or RAL 9016 white (C16), matte finish.
AISI 304 stainless steel boss, threaded blind hole.
The special antibacterial additive prevents bacteria on the product surface.
The controlled release mechanism of the silver ions keeps the antibacterial characteristics unchanged over time, even after several washing cycles. Furthermore the material additives are metal detectable at a cubic particle size of 5mm per side. The high temperature resistance of the additive used allows its use even in sterilisation cycles (130°C).
It's therefore suitable for applications where sanitation and hygiene are fundamental, for example:
- Medical and hospital equipment;
- Disability aids;
- Machines for food processing and pharmaceutical industry;
- Equipment for catering service;
- Urban and public fittings.
Glass-fibre reinforced polyamide based (PA) with silver ion additive on an inorganic base, RAL 7021 grey-black colour (C1) or RAL 9016 white (C16), matte finish.
The special antibacterial additive prevents bacteria on the product surface. The controlled release mechanism of the silver ions keeps the antibacterial characteristics unchanged over time, even after several washing cycles. Furthermore the material additives are metal detectable at a cubic particle size of 5mm per side. The high temperature resistance of the additive used allows its use even in sterilisation cycles (130°C). It's therefore suitable for applications where sanitation and hygiene are fundamental, for example:
- Medical and hospital equipment;
- Disability aids;
- Machines for food processing and pharmaceutical industry;
- Equipment for catering service;
- Urban and public fittings.
Material:
MATERIAL
Glass-fibre reinforced polyamide based (PA) technopolymer, with silver ion additive on an inorganic base, RAL 7021 grey-black colour
(C1) or RAL 9016 white (C16), matte finish.
AISI 304 stainless steel boss, threaded blind hole.
E+G EWN-LP wing nut with retaining chain.
The elastic fork, housed in the groove of the wing nut can turn freely. The coiled ring connects the fork to the chain. Suitable where it is necessary to prevent the loss of the wing nut. For applications in which the fixing of the chain is at a position higher than that of the wing nut, it is advisable to leave it with slack movement to prevent the ring from touching the wing nut.
Material:
Wing nut in glass-fibre reinforced polyamide based (PA) technopolymer, greyblack colour, matte finish.
Elastic fork in acetal based technopolymer (POM), black colour
Boss cap in Polyamide based (PA) technopolymer, grey-black colour, matte finish, press-fit assembly, removable by a screwdriver.
Retaining chain: Ball cable and coupling heads in acetal resin based (POM) technopolymer, black colour.
NERINOX treated stainless steel ring with two coils.
Head fastening by means of a self-tapping screw ø4.8 mm UNI EN ISO 7050 or a M5 countersunk-head screw UNI EN ISO 10642.
Standard executions:
- EWN-B-LP: brass boss, threaded through hole.
- EWN-SST-LP: AISI 303 stainless steel, threaded pass-through hole.
- EWN-p-LP: zinc-plated steel threaded stud, chamfered flat end according to UNI EN ISO 4753:2012.
- EWN-SST-p-LP: AISI 303 stainless steel threaded stud, chamfered flat end UNI EN ISO 4753:2012.
Retaining chain is 200 mm long. Other lenghts on request.
Elesa+Ganter GN VB.839 three-arm-knob with coloured centre cap.
The three-arm shape is particularly ergonomic, ensuring an excellent grip. Winner of the Red Dot award 2019.
Material:
- Glass-fibre reinforced polyamide based (PA) technopolymer, polyamide based (PA) technopolymer coating, chemically bonded with semi-glossy finish, black colour.
- Coloured centre cap in Polyamide based (PA) technopolymer, in the standard colours, semi-glossy finish.
Standard executions:
- VB.839-B: brass boss, threaded blind hole.
- VB.839-SST: AISI 303 stainless steel boss, threaded blind hole.
- VB.839-p: zinc-plated steel threaded stud, chamfered flat end according to UNI 947 : ISO 4753 (see datasheet).
Coloured centre cap:
- C9: Black RAL9005
- C2: Orange RAL2004
- C3: Grey RAL7035
- C4: Yellow RAL1021
- C5: Blue RAL5024
- C6: Red RAL3000
- C17: Green RAL6017
Elesa+Ganter VB.839 SOFT soft-touch three-arm knob with coloured centre cap
The soft coating makes it more comfortable to use even in the presence of humidity and is particularly useful in the case of prolonged use or in the presence of disabilities as well as allowing greater tightening torque. The three-arm shape is particularly ergonomic. The product design associated with the soft coating gives the machinery to which it is applied an air of quality and refinement. Red Dot award winner 2019.
Material:
- Glass-fibre reinforced polyamide based (PA) technopolymer, coated "soft-touch" thermoplastic elastomer (TPE) chemically bonded, hardness 70 Shore A, black colour, matte finish.
- Coloured centre cap in pPolyamide based (PA) technopolymer, in the standard colours, semi-glossy finish.
Standard executions:
- VB.839-B-SOFT: brass boss, threaded blind hole.
- VB.839-SST-SOFT: AISI 303 stainless steel boss, threaded blind hole.
- VB.839-p-SOFT: zinc-plated steel threaded stud, chamfered flat end according to UNI 947 : ISO 4753 (see datasheet).
Coloured centre cap:
– C9: Black RAL9005
– C2: Orange RAL2004
– C3: Grey RAL7035
– C4: Yellow RAL1021
– C5: Blue RAL5024
– C6: Red RAL3000
– C17: Green RAL6017
Elesa+Ganter VTT-HL star knob with hexagonal shank allows the handwheel to be tightened with a spanner. The three-lobe shape with large recesses is particularly ergonomic also for smaller knobs, ensuring an effective grip even with work gloves. The full section design without rear cavities prevents the deposit of unsanitary residues, ensuring maximum cleanability and making the product particularly suitable for applications on machines and equipment subject to frequent cleaning with water or steam jets.
Material:
- Glass-fibre reinforced polyamide based (PA) technopolymer, black colour, matte finish.
Standard executions:
- VTT-HL-AZ: Zinc-plated hexagonal shank, threaded blind hole.
- VTT-HL-SST: AISI 304 stainless steel hexagonal shank, threaded blind hole.
Elesa+Ganter BTL grip knob.
Material:
Polyamide based (PA) technopolymer, black colour, matte finish.
Standard executions:
- BTL-B: brass boss, threaded blind hole.
- BTL-p: zinc-plated steel threaded stud, chamfered flat end according to UNI 947 : ISO 4753 (see Technical data).
Elesa+Ganter BT-SST-p-SV fluted grip knob.
The BT-SST-p-SV knobs allow the locking of a component avoiding, thanks to the thrust pad, direct contact of the stud with the surface to be locked. The metal insert in AISI 303 stainless steel can be used in sectors where corrosion resistant materials are required.
Material:
- Polyamide-based (PA) technopolymer knob, black colour, matte finish.
- AISI 303 stainless steel threaded stud, spherical end.
- Acetal resin based (POM) technopolymer thrust pad, black colour, matte finish, supplied not assembled.
Elesa+Ganter BT-AV fluted grip knob. The slot in the upper part of the knob is an ideal support when you have to tighten with a 6.5 mm flat-blade screwdriver.
Elesa+Ganter Stainless Steel-Star knobs GN 6336 satisfy the dimensions of the DIN 6336 but differ in terms of their non-scooping geometry, which makes cleaning easier and helps prevent possible build-up of dirt.
They are suitable for areas with special hygiene requirements and, thanks to the material used, for applications in highly corrosive environments.
Types:
- Type D: with threaded through bore
- Type E: with threaded blind bore
Material:
Stainless Steel precision casting A4, AISI 316, polished PL
Elesa+Ganter VC.692-SST-p-SV lobe knob
The VC.692-SST-p-SV knobs allow the locking of a component avoiding, thanks to the thrust pad, direct contact of the stud with the surface to be locked. The metal insert in AISI 303 stainless steel can be used in sectors where corrosion resistant materials are required.
Material:
– Polyamide-based (PA) technopolymer knob, black colour, matte finish.
– AISI 303 stainless steel threaded stud, spherical end.
– Acetal resin based (POM) technopolymer thrust pad, black colour, matte finish
Supplied not assembled.
E+G GN 8340 is stainless steel wing nuts that clamp and fasten parts easily without tools.
E+G GN 8341 is a wingnut in stainless steel AISI316 from Elesa+Ganters Hygenic Design series.
Wing nuts GN 8341 are intended for use in hygienic areas. The sealed mounting surface enables mounting without dead spaces; the impervious geometry in combination with the high quality finish prevents the accumulation of dirt and facilitates cleaning. Wing nuts clamp and fasten parts easily without tools. The ergonomic shape allows for high tightening forces.
The wing nuts can also be used in particularly aggressive environments thanks to the material used.
Material
- Housing in Stainless steel AISI 316
- Choose between two different types of blue sealing ring which both are 85 ±5 Shore A in hardness and FDA compliant:
- H-NBR H, temperature resistant -25 °C to +150 °C
- EPDM E, temperature resistant -40 °C to +120 °C
Execution
– Matte finish (MT)
– Polished finish (PL)
Benifits for you as a customer at Brd. Klee
Benifits for you as a customer at Brd. Klee
